View MC100H602_82978.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
9-Bit Latch TTL/ECL Translator
The MC10H/100H602 is a 9-bit, dual supply TTL to ECL translator with latch. Devices in the Motorola 9-bit translator series utilize the 28-lead PLCC for optimal power pinning, signal flow-through and electrical performance. The H602 features D-type latches. Latching is controlled by Latch Enable (LEN), while the Master Reset input resets the latches. A post-latch logic enable is also provided (ENECL), allowing control of the output state without destroying latch data. All control inputs are ECL level. The 10H version is compatible with MECL 10H ECL logic levels. The 100H version is compatible with 100K levels. * * * * * * 9-Bit Ideal for Byte-Parity Applications Flow-Through Configuration Extra TTL and ECL Power/Ground Pins to Minimize Switching Noise Dual Supply 3.5 ns Max D to Q PNP TTL Inputs for Low Loading
MC10H602 MC100H602
FN SUFFIX PLASTIC PACKAGE CASE 776-02
PIN NAMES
PIN GND VCCE VCCO VCCT VEE D0 - D8 Q0 - Q8 ENECL LEN MR FUNCTION TTL Ground (0 V) ECL VCC (0 V) ECL VCC (0 V) -- Outputs TTL Supply (+ 5.0 V) ECL Supply (- 5.2 / - 4.5 V) Data Inputs (TTL) Data Outputs (ECL) Enable Control (ECL) Latch Enable (ECL) Master Reset (ECL)
LOGIC SYMBOL
ENECL D0 DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN DQ EN Q0
D1
Q1
TRUTH TABLE
D LEN L L H X X MR L L L H X ENECL H H H H L Q L H Q0 L L
D2
Q2
D3
Q3
L H X X X ECL
TTL
D4
Q4
Pinout: 28-Lead PLCC (Top View)
Q5
D6
26 27 28
D5
D5 D4 VCCT D3
25 24 23 22
D2 D1 D0
21 20 19 18 17 16 15
D6
Q0 Q1 VCCE VCCO Q2 VCCO Q3
Q6
D7 D8
D7
Q7
GND MR
2 3 4 5 6 7 8 9 10 11
14 13 12
D8 LEN MR
Q8
LEN ENECL
Q8 Q7 VCCO Q6 VEE Q5 Q4
3/93
(c) Motorola, Inc. 1996
2-307
REV 5
MC10H602 MC100H602
DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version)
0C Symbol S bl Parameter P Power Supply Current IEE ICCH ICCL ECL TTL 10H 100H -125 -122 48 50 -125 -123 48 50 -125 -132 48 50 mA mA Min Max Min 25C Max Min 75C Max Unit Ui Condition C di i
AC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version)
0C Symbol S bl tPLH tPHL Parameter P Propagation Delay to Output D LEN MR ENECL Min 1.4 2.0 2.0 1.6 2.0 1.0 2.0 0.5 1.5 Max 3.0 3.4 3.4 3.2 Min 1.5 2.1 2.1 1.7 2.0 1.0 2.0 0.5 1.5 25C Max 3.2 3.5 3.5 3.3 Min 1.7 2.4 2.5 1.8 2.0 1.0 2.0 0.5 1.5 75C Max 3.5 3.7 3.9 3.7 Unit Ui ns Condition C di i
ts th tw(L) tR tF
Set-Up Time, D to LEN Hold Time, D to LEN LEN Pulse Width, LOW Output Rise/Fall Time 20% - 80%
ns ns ns ns
10H ECL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5%
0C Symbol S bl IIH IIL VIH VIL VOH VOL Parameter P Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage Output HIGH Voltage Output LOW Voltage Min 0.5 -1170 -1950 -1020 -1950 - 840 -1480 - 840 -1630 Max 225 0.5 -1130 -1950 - 980 -1950 - 810 -1480 - 810 -1630 Min 25C Max 145 0.5 -1070 -1950 - 920 -1950 - 735 -1450 - 735 -1600 Min 75C Max 145 Unit Ui A A mV mV 50 to - 2.0 V Condition C di i
100H ECL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 4.2 V to - 5.5 V
0C Symbol S bl IIH IIL VIH VIL VOH VOL Parameter P Input HIGH Current Input LOW Current Input HIGH Voltage Input LOW Voltage Output HIGH Voltage Output LOW Voltage Min 0.5 -1165 -1810 -1025 -1810 - 880 -1475 - 880 -1620 Max 225 0.5 -1165 -1810 -1025 -1810 - 880 -1475 - 880 -1620 Min 25C Max 145 0.5 -1165 -1810 -1025 -1810 - 880 -1475 - 880 -1620 Min 75C Max 145 Unit Ui A A mV mV 50 to - 2.0 V Condition C di i
TTL DC CHARACTERISTICS: VCCT = 5.0 V 10%; VEE = - 5.2 V 5% (10H version); VEE = - 4.2 V to - 5.5 V (100H version)
0C Symbol S bl VIH VIL IIH IIL VIK Parameter P Input HIGH Voltage Input LOW Voltage Input HIGH Current Input LOW Current Input Clamp Voltage Min 2.0 0.8 20 100 - 0.6 -1.2 Max Min 2.0 0.8 20 100 - 0.6 -1.2 25C Max Min 2.0 0.8 20 100 - 0.6 -1.2 75C Max Unit Ui V V A mA V VIN = 2.7 V VIN = 7.0 V VIN = 0.5 V IIN = -18 mA Condition C di i
MOTOROLA
2-308
MECL Data DL122 -- Rev 6
MC10H602 MC100H602
OUTLINE DIMENSIONS
FN SUFFIX PLASTIC PLCC PACKAGE CASE 776-02 ISSUE D
B -N- Y BRK U D Z -L- -M- 0.007 (0.180)
M
0.007 (0.180)
M
T L-M
S
N
S S
T L-M
N
S
W
28 1
D
X VIEW D-D
G1
0.010 (0.250)
S
T L-M
S
N
S
V
A Z R C
0.007 (0.180) 0.007 (0.180)
M
T L-M T L-M
S
N N
S
H
0.007 (0.180)
M
T L-M
S
N
S
M
S
S
E 0.004 (0.100) G G1 0.010 (0.250)
S
K1
J
-T- VIEW S
SEATING PLANE
K F VIEW S 0.007 (0.180)
M
T L-M
S
N
S
T L-M
S
N
S
NOTES: 1. DATUMS -L-, -M-, AND -N- DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM -T-, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635).
DIM A B C E F G H J K R U V W X Y Z G1 K1
INCHES MIN MAX 0.485 0.495 0.485 0.495 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 --- 0.025 --- 0.450 0.456 0.450 0.456 0.042 0.048 0.042 0.048 0.042 0.056 --- 0.020 2_ 10_ 0.410 0.430 0.040 ---
MILLIMETERS MIN MAX 12.32 12.57 12.32 12.57 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 --- 0.64 --- 11.43 11.58 11.43 11.58 1.07 1.21 1.07 1.21 1.07 1.42 --- 0.50 2_ 10_ 10.42 10.92 1.02 ---
MECL Data DL122 -- Rev 6
2-309
MOTOROLA
MC10H602 MC100H602
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298
MOTOROLA 2-310
*MC10H602/D*
MC10H602/D MECL Data DL122 -- Rev 6

▲Up To Search▲

Price & Availability of MC100H602

	To Download MC100H602 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .